Do to circumstances beyond my control
I will be back at a later date
I am OUT of QUEENS until Further Notice!
QUEENS
1 to 4 ------------$30.00 each
5 to 10 -----------$28.00 each
11-25 ------------$24.00 each
26 and up --------$20.00 each
I DO NOT CLIP WINGS
QUEENS ARE MARKED GREEN FOR 2019 -- FREE!
RV BEES 501-593-5324
email: capt44@rvbees.com
BELOW IS A LIST OF DIFFERENT PAGES. JUST CLICK ON THE PAGE AND SCROLL DOWN BELOW THE AD.
RV BEES "THE BEE GUY"
116 White Wolf Tr
Searcy, AR 72143-8775
ph: 501-593-5324
capt44
There are 3 different Hive Plans I want to pass on to the Beekeepers.
1. The Langstroth bee hive, patented in October 1852, is the standard beehive used in many parts of the world for beekeeping. The advantage of this hive is that the bees build honeycomb into frames, which can be moved with ease.
2. A top-bar hive is a single-storey frameless beehive in which the comb hangs from removable bars. Hives that have frames or that use honey chambers in summer but which use similar management principles as regular top-bar hives are sometimes also referred to as top-bar hives.
3. The Long Box Hive is a single story hive utilizing fully ... Idea Hive", "Single Story Hive", "Poppleton Hive", or simply "Long Hive".
Langstroth Hive Plans
1. Plans for the Top, Inner Cover and Bottom Boards
----------------------------------------------------------------------
LONG HIVE
Plans furnished by
Dr. Leo Sharashkin
Materials list
Tools list
You can complete this project using a variety of tools. This is what I use:
Building instructions
Step 1. Cut the “two-by-twelve” board into four pieces: 44-13/16” (2) and 21-3/8” (2). These are the walls. Mark the sides that will face outside. (Usually, the better-looking surfaces look outside. Also, the outer side of year rings should preferably face outside. If the board is slightly cupped, the concave side should look inside.)
Step 2. Check the width at both ends of each board that you’ve cut. The “two-by-twelve” lumber is supposed to be exactly 11-1/4” wide, but in reality it can be off by up to 1/8”, and one end of the board can be wider than the other. If all four pieces you cut have exactly the same width at both ends, all is good. If not — run them all through the table saw so the width is uniform (e.g., 11-1/8”).
Step 3. Cut a rabbet 3/8” by 3/4” along the top inner edge of the long boards. These are frame rests.
Step 4. Cut three entrances in the front wall. Each entrance is a slot 6” wide by 1/2” tall. They are 1-1/4” from the bottom edge of the board; 2” from each end, and in the center. To cut an entrance, drill a 1/2” hole then use a router with a 1/2” straight bit. (If you do not have a router, you can use a jigsaw instead.)
Step 5. Assemble the hive box. The long walls go between the end walls. Put them on a completely flat surface (e.g., concrete floor), the bottom side facing up (and rabbeted frame rests facing inside!). Clamp all four corners using right angle clamps. Assemble with 3-1/2” screws, three screws per corner. Do drill pilot holes to prevent board from cracking.
Step 6. Cut a rabbet (3/4” wide by 1/2” deep) along the entire inner perimeter of the hive box. The bottom will go into this groove. (Alternative: if you do not have a router to cut this rabbet, you can just screw the bottom onto the hive box, with no rabbet cut. In this case you should rip all four walls down to 10-3/4” width in Step 2.)
Step 7. Cut plywood as shown below. You will have the following parts, enough for exactly two hives:
Step 8. Insert the bottom and attach it to the hive body with 1-1/8” deck screws. Do not use glue so you can remove the bottom in the future, if needed (e.g., for cleaning or to install a screen bottom board).
Step 9. Cut the “two-by-four” at 45° as shown. Make sure that the 1-1/2” (narrow) side faces up. Measure 30-1/2” on both ends and make angle cuts first. This will produce four 30-1/2” legs with one end slanted at 45°.
Step 10. Turn the hive body on its side. Mark 2” from the top edge of the box on the end wall. Position a leg and attach it with two 3-1/2” screws (marked X) and one 2-1/2” screw (marked O). Attach another leg on the opposite end wall. Then flip the box over and attach two more legs.
Step 11. Tilt the table saw 15° and run the landing board strip through it, removing one edge. You’ll have a strip approx. 1-11/16” wide, with one long edge cut at an angle. Cut the strip into six landing boards 7-1/2” long. It makes for a small, yet adequate landing board. If you have scrap pieces of larger boards lying around, you can make the landing board larger, up to 10” long by 3-1/2” wide.
Step 12. Center the landing strip under the entrance and attach to the hive body with two 1-1/8” screws, one on each side of the entrance. Pre-drilling the landing board is essential to prevent splitting. Repeat with the remaining two entrances. Your hive box is now ready!
Step 13. Now let’s assemble the top. The cut of the plywood allows for 1-1/4”-deep rim on one top, and 1-3/4”-deep rim on the other. In the 1-1/4” rim the short strips (Strip-1-Short, part b) go between the long strips (Strip-1-Long, part a). In the 1-3/4” rim the long strips (Strip-2-Long, part c) go between the short strips (Strip-2-Short, part d). Clamp rim strips at right angles, pre-drill, and connect on 1-1/8” screws, one or two per corner.
Step 14. Apply wood glue and attach the top plywood panel. If you have a pneumatic staple gun, use it with 1” staples. Otherwise pre-drill and assemble on 1-1/8” screws.
Step 15. Cut a piece of insulation board 48” x 21-5/8” and insert it into the top. It will fit tightly and will usually stay put. If not, use some construction glue to secure it to the top.
Step 16. Apply two coats of primer/sealer, and then one coat of light-colored paint on all exterior surfaces of the hive box, legs, and top. Pay special attention to exposed edges of plywood and board. The hive is ready!
Considerations
You now have the finished Long Langstroth Hive.
Kenya Top-Bar Hive Plans
If you're interested in giving beekeeping a try on more of a shoestring budget, a top-bar hive might be for you. The whole idea behind a top-bar hive is simplicity, so it can be made with the least amount of materials and tools when both are scarce and hard to come by. Not everyone likes simple, but I do.
This hive can be built in a weekend, and you can leave it basic or fancy it up as much as you want.
BELOW IS A BLOW-UP OF A TOP BAR HIVE
SIDES
Inside look at a working Top Bar Hive.
Copyright 2013 RV BEES. All rights reserved.
RV BEES "THE BEE GUY"
116 White Wolf Tr
Searcy, AR 72143-8775
ph: 501-593-5324
capt44